Spaenaur Catalog 14 - Digital Flipping Catalog

CATALOG 14 E P : 1-800-265-8772 F : 1-888-252-6380 www. .com Lynch Pins Metric Métrique E67 Conforms to ISO/DIS 7072 and meets requirements of DIN 11023 (1979) (German industrial specifications) The need for a better quality lynch pin became apparent when the trend towards larger horsepower tractors pulling wider and heavier implements was growing. Rübig responded to the need by perfecting their Safety Lynch Pin with a breaking strain approx. 3 times greater than normal lynch pins (68 to 88 tons per square inch), and with the following features: 1) Safety catch in shaft of pin into which the spring snapped tight (US Patent No. 3926089). 2) Extra hole in top of pin to take safety chain. 3) Best quality spring steel ring passing right through the pin at its hinge points. 4) Zinc electroplate finish. The need for security! Reduces damage to machinery, loss of time, and dangerous situations caused by lynch pin failure. It makes good sense to use these high quality pins on your equipment. Why a safety catch? Suitable for extreme conditions, this pin should be used, for example, ● when the implement is very near to the ground: ploughing, cultivating, harrowing ● working inwoodlands and scrub areas, where branches and tree stumps can easily push other pins out ● in the vineyards ● bracken cutting ● hitch points on trailer Actual Size Illustrations on Page E68 Attention: Don’t put your finger between ring and shaft when you close the pin. DIN 11023 SPAENAUR Ø Ø Ø Shaft No. d1 L1 L2 h b1 b2 b3 d2 d3 Ød4 a 233-050 7.5 42 62 7 13.5 7.5 50 4 3.6 32 7.5 233-051 9.5 45 66 11 14 8 50 4.5 3.6 32 8 233-052 10.5 45 66 11 14 8 50 4.5 3.6 32 8.5 233-053 11.5 45 66 11 14 9 50 4.5 3.6 32 9 233-054 233-049 11.5 65 85 11 21.5 9 50 4.5 - 32 9 11.5 55 77 8 15 9 59 4.5 4 45 9 *Yellow Zinc Permissible deviation: d1 of 4.5 to 9.5 +0.3-0.2; PKG QTY. 5 ±0.5 Dimensions in Millimeters RÜBIG Safety Lynch Pin - SPECIFICATIONS Drop-forged steel shaft, hardened and tempered to a strength of 110-140 kp/mm2, the spring is made of spring steel wire in accordance with DIN 17233. Both shaft and spring are galvanized, layer thickness: 10-12 micron, yellow chromatized. After assembly, each individual safety lynch pin is tested for correct functioning and springopening power. (Spring-opening force: 80-120N). The minimum values required by DIN 11023 are exceeded considerably by all RÜBIG-Safety Lynch Pins, and they are officially tested (“Wieselburg”), recognized by the DLG (agricultural association of Germany), and sizes 7.5 and 10.5 are also available in stainless steel. Naturally, to give such benefits has not been achievedwithout considerable cost, andwhile the initial purchase price is greater, true costs in terms of longer life, greater security, not lost so easily, are a fraction of the price normally paid for the common lynch pin. *233-055ZP 15.5 60 80 12 17.5 14.5 68 6 4 45 12.5 28 APR 2022 PKG QTY. 10 ■ ■ ◆ ◆ Clavettes d'essieu : F : 1- 8-252-6380 service@spaenaur © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue. CAT LOG 14.09

RkJQdWJsaXNoZXIy NzkyNDk4