CATALOG 14 E P : 1-800-265-8772 F : 1-888-252-6380 www. .com Inch Pouce External Retaining Rings E137 19 Jan 2018 277-001 5/32 .156 (4.0) .110 .025 .320 .120 .029 .018 325 110 277-002 3/16 .188 (4.8) .140 .025 .400 .148 .029 .020 436 130 277-003 1/4 .250 (6.4) .188 .025 .482 .210 .029 .020 650 200 277-004 5/16 .312 (7.9) .250 .025 .588 .272 .029 .020 792 250 277-005 3/8 .375 (9.5) .312 .035 .680 .331 .039 .022 1320 300 277-006 7/16 .438 (11.1) .375 ±.004 .035 .752 .390 .039 .024 1878 400 277-007 1/2 .500 (12.7) .406 .042 .826 .440 .046 .030 2132 600 277-008 5/8 .625 (15.9) .500 .042 .966 .531 .046 .047 2538 1100 277-009 3/4 .750 (19.0) .594 .050 1.095 .632 .056 .059 3756 1600 *277-010 1 1.000 (25.4) .812 ±.006 .050 1.415 .860 .056 .070 4872 2600 S S S D tol. t tol. Y G tol. W tol. d P r P g 277-015 5/32 .156 (4.0) .110 .035 .320 .120 .039 .018 457 110 277-018 3/16 .188 (4.8) .140 .035 .400 .148 .039 .020 609 130 277-025 1/4 .250 (6.4) .188 .035 .482 .210 .039 .020 914 200 277-031 5/16 .312 (7.9) .250 .042 .588 .272 .046 .020 1320 250 277-037 3/8 .375 (9.5) .312 .042 .680 .331 .046 .022 1573 300 277-043 7/16 .438 (11.1) .375 ±.004 .050 .752 .390 .056 .024 2233 400 277-050 1/2 .500 (12.7) .406 .050 .826 .440 .056 .030 2538 600 *277-062 5/8 .625 (15.9) .500 .050 .966 .531 .056 .047 3045 1100 *277-075 3/4 .750 (19.0) .594 .062 1.095 .632 .068 .059 4669 1600 *277-100 1 1.000 (25.4) .812 ±.006 .078 1.415 .860 .086 .070 7613 2600 ±.005 KLIPRING The Klipring is a unique heavy-duty radially-assembled ring which provides substantially greater gripping strength and load capacity than conventional E-rings and similar fasteners. It is thicker than conventional rings, and has tapered-section bending arms which exert very strong spring pressure when the ring is assembled. Kliprings can be assembled easily with an ordinary pair of slip-joint pliers, or can be tapped into a groove with amallet or hammer. A screw driver inserted under the tapered section can be used to pry the ring off the shaft quickly. The ring is reusable following disassembly. *Configuration of 277-062,-075, -100 and -010. SHAFT DIAMETER Fract. Dec. equiv. equiv. (Approx. inch inch mm) DIAMETER WIDTH RINGS (Standard material) Safety factor =2-1/2 Important GROOVES (Cold rolled steel shafts) Safety factor =2 ALLOW. THRUST LOAD (lbs.) Sharp Corner Abutment +.006 -.000 +.008 -.000 ±.003 FREE DIA. Nominal groove depth T.I.R. (total indicator reading) is the maximum allowable deviation of concentricity between groove and shaft. ±.006 .003 TIR ±.010 .004 TIR ±.004 .002 TIR ±.005 .002 TIR ±.008 .003 TIR ±.008 .004 TIR ±.002 ±.003 ±.005 +.006 -.000 +.008 -.000 ±.003 ±.006 .003 TIR ±.010 .004 TIR ±.004 .002 TIR ±.005 .002 TIR ±.008 .003 TIR ±.008 .004 TIR ±.002 THIN SERIES KLIPRING HEAVYDUTY KLIPRING SPAENAUR No. GROOVE DIMENSIONS STEEL The Klipring is designed to be installed in a deep groove, having a larger diameter than the ring’s free diameter. The ring also can be used as a spacer washer - it is merely slipped over a shaft of the same diameter as the ring’s free diameter. Thickness “t” applies only to unplated rings. For plated rings, add .002" to the listedmaximum thickness. Maximum ring thickness will be at least .0002" less than the listed minimum groove width (W). t Y S W G D I d I HEAVY DUTY SERIES THICKNESS RING DIMENSIONS Free outside (In Inches) (In Inches) Finish: Plain or Phosphate, at our option. PKG QTY. 100 Bagues de retenue externes F : 1- 8-252-6380 service@spaenaur. © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue.
RkJQdWJsaXNoZXIy NzkyNDk4