CATALOG 14 B P : 1-800-265-8772 F : 1-888-252-6380 www. .com Inch Pouce Eye Bolts B267 27 APR 2022 024-044 1/4-20 2.00 0.50 0.94 3.19 0.75 10 024-022 1/2-13 6.00 1.00 1.938 8.00 1.25 5 SHOULDER TYPE FORGED / 1030 STEEL / HEAT TREATED Self-Coloured C D F E B A EYE BOLTS No. 024-044 Hot Galvanized Finish. 1" Thread Length. • Hot Galvanized Finish. 2" Thread Length. Self-coloured finish except: (In Inches) (D) (F) (A) (B) (C) Nom (E) Centre SPAENAUR Thread Shank Eye Eye Overall Of Eye To PKG No. Size Length I.D. O.D. Length Shoulder QTY. EYB-3 1/4-20 1.00 0.50 0.94 2.20 0.70 10 EYB-4 1/4-20 1.00-1.06 0.69-0.81 1.19 2.22-2.53 0.69-0.81 10 EYB-5 5/16-18 1.125 .625 1.19 2.50 0.875 10 024-T38-1X 5/16-18 1.12-1.19 0.81-0.94 1.44 2.66-2.97 0.88-1.00 10 EYB-7 3/8-16 0.75 1.00 1.69 2.81 1.20 10 EYB-8 3/8-16 1.25 0.75 1.44 2.97 1.00 10 EYB-9 3/8-16 1.25-1.38 0.94-1.06 1.69 3.09-3.47 1.06-1.19 10 EYB-10 7/16-14 1.38-1.50 1.00-1.12 1.81 3.41-3.78 1.19-1.31 10 EYB-11 1/2-13 1.50 1.00 1.94 3.75 1.28 5 EYB-12 1/2-13 1.50-1.62 1.12-1.25 2.12 3.81-4.19 1.31-1.44 5 EYB-13 9/16-12 1.75-1.88 1.31-1.44 2.56 4.56-4.94 1.59-1.72 5 EYB-14 5/8-11 1.75-1.88 1.31-1.44 2.56 4.56-4.94 1.59-1.72 5 EYB-15 3/4-10 2.00-2.12 1.44-1.56 2.81 5.06-5.50 1.72-1.91 5 EYB-16 7/8-9 2.25-2.38 1.56-1.69 3.19 5.75-6.19 2.03-2.22 1 EYB-17 1-8 2.50-2.62 1.69-1.81 3.56 6.44-6.88 2.22-2.41 1 EYB-18 1-1/8-7 2.75-2.88 1.94-2.06 4.06 7.31-7.75 2.59-2.78 1 EYB-19 1-1/4-7 3.00-3.12 2.12-2.25 4.44 8.00-8.44 2.84-3.03 1 EYB-20 1-1/2-6 3.50-3.62 2.44-2.56 5.19 9.22-9.72 3.19-3.44 1 EYB-40 1-3/4-5 3.75-3.88 2.75-3.00 6.00 10.50-11.12 3.88-4.12 1 -Special Stock Sizes - SHANKS FULL THREADED TO WITHIN 1/8" - 3/8" OF SHOULDER. Class 2A (UNC-2A) (COARSE THREAD) WARNING: APPLIES TO EYE BOLTS & EYE NUTS Safe working load is drastically reduced when loading at an angle. Loading must never be made at an angle greater than 45° from bolt or nut centreline. Plane of the Eye Shoulder Pattern Eyebolt Showing Rated Capacity in lbs. at 0° and 45° (for ref. only) Plain Pattern (Straight Shank) Eyebolt Showing Rated Capacity in lbs. at 0° (for ref. only) Note: All Eye Bolts and Eye Nuts, whether in blanks or fully machined, as shown on page B269, are covered by our standard warranty. The warranty becomes VOID whenever modifications are made or further machining is done by the buyer, also in cases where these items are subject to an angular lift or pull. ASME B18.15 Boulons à œil ▲ ▲ Nominal Size Rated Cap. in lbs. 0 Degrees 1/4" 500 5/16" 900 3/8" 1,400 7/16" 2,000 1/2" 2,600 9/16" 3,200 5/8" 4,000 3/4" 6,000 7/8" 7,000 1" 9,000 1-1/8" 12,000 1-1/4" 15,000 1-1/2" 21,000 1-3/4" 24,700 2" 32,500 2-1/2" 52,000 Rated Cap. in lbs. Rated Cap. in lbs. Nominal Size 0 Degrees 45 Degrees 1/4" 500 125 5/16" 900 225 3/8" 1,400 350 7/16" 2,000 500 1/2" 2,600 650 9/16" 3,200 800 5/8" 4,000 1,000 3/4" 6,000 1,500 7/8" 7,000 1,750 1" 9,000 2,250 1-1/8" 12,000 3,000 1-1/4" 15,000 3,750 1-1/2" 21,000 5,250 1-3/4" 24,700 8,250 2" 32,500 101,910 : F : 1- 8-252-6380 service@spaenaur © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue. CAT LOG 14.09
RkJQdWJsaXNoZXIy NzkyNDk4