CATALOG 14 B P : 1-800-265-8772 F : 1-888-252-6380 www. .com Inch Pouce Self-Clinching Studs B126 THREAD SIZE (L) Length in inches ORDER BYSPAENAUR No’sLISTED BELOW 2-56 MATERIAL AND FINISHES STEEL Carbon Steel, Heat Treated, Zinc or Cadmium Plated, QQ-P-416, Type 1, Class 3, Plus Clear Chromate Dip STAINLESS STEEL (S.S.) 300 Series Stainless Steel (Passivated, QQ-P-35, Type I) ALUMINUM (ALUM.) 2024-T4 Aluminum ANVIL DIMENSIONS THREAD ANVIL SIZE B T .110 .087 .114 .090 .136 .113 .140 .116 .162 .139 .166 .142 .188 .165 .192 .168 .216 .191 .220 .194 .295 .250 .300 .253 .3125 .3155 INSTALLATION NOTE: Apply only sufficient squeezing pressure to embed head of stud flush with panel. Do not usemore pressure than necessary. Amount of pressure varies with panel metal and size of stud. Studs install flush in sheets .040" or thicker, but will project up to .020" in thinner sheets. STEEL ALUM 2-56 2-1/2 3000 2000 4-40 5 4000 3000 6-32 10 4500 3500 8-32 20 5000 4000 10-24 25 6000 4500 10-32 35 6000 4500 1/4-20 80 7000 5000 5/16-18 140 8000 6000 Note: These values are for general reference only. *Maximum nut tightening values THREAD SIZE *Torque (IN-LB) Installation (LB) Steel Stainless Steel Aluminum 2-56 4-40 6-32 8-32 10-24 1/4-20 5/16-18 THREAD Class 2A (MIL-S-7742) INSTALLATION USE THIS ANVIL For panels .060" andmore in thickness, with #2 thru #10 thread sizes. For panels .093" and more in thickness, with 1/4" and 5/16" thread sizes. USE THIS ANVIL For panels less than .060" in thickness, with #2 thru #10 thread sizes. For panels less than .093" in thickness, with 1/4" thread size. GENERAL TOOLING SETUP See WELDING SCREWS on pages B128-B133 Kind of Metal Min. Edge Distance to center of Hole in Panel Hole in Sheet +.003 -.000 D. Head Dia. ±1/64 5/16"-18 1/4"-20 10-32 10-24 8-32 6-32 4-40 Inch Sizes DIMENSIONS & SPECIFICATIONS: STEEL 614-003 614-004 614-005 9/64 .085 .19 S.S. 614-808 614-809 614-810 614-811 614-812 STEEL 614-006 614-007 614-008 614-009 614-010 614-011 3/16 .111 .22 S.S. 614-813 614-814 614-800 614-801 614-815 614-816 ALUM. 614-300 614-301 STEEL 614-057 614-012 614-013 614-014 614-015 614-016 614-017 614-018 614-019 13/64 .137 .25 S.S. 614-817 614-802 614-803 614-818 614-819 614-820 614-821 ALUM. 614-302 614-C03-1W 614-312 614-313 STEEL 614-020 614-021 614-022 614-023 614-024 614-025 614-026 614-027 15/64 .163 .28 S.S. 614-822 614-804 614-805 614-823 614-824 614-825 ALUM. STEEL 614-028 614-029 614-030 614-031 614-032 614-033 614-034 1/4 .189 .28 S.S. 614-826 614-827 614-828 614-829 614-830 614-831 ALUM. 913-416 503-416 STEEL 614-036 614-037 614-038 614-039 614-040 614-041 614-042 614-043 1/4 .189 .28 S.S. 614-832 614-806 614-807 614-833 614-834 ALUM. 614-306 614-321 STEEL 614-044 614-045 614-046 614-047 614-048 614-050 21/64 .249 .31 S.S. 614-835 614-841 614-836 614-837 ALUM. 614-307 614-323 STEEL 614-051 614-052 614-053 614-054 614-055 614-056 25/64 .311 .38 S.S. 614-838 614-839 614-840 ALUM. 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 614-C01-1T PKG QTY. 100 614-314 13 MAR 2018 Goujons autoriveurs F : 1- 8-252-6380 service@spaenaur © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue.
RkJQdWJsaXNoZXIy NzkyNDk4